|
Re-enamelling a cast iron bath
Messages 221
to 240
of
834.
« Previous
1
...
6
7
8
9
10
11
12
13
14
15
16
17
18
...
42
Next »
 |
Re-enamelling a cast iron bath
2 November 2004, 12:17 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Hello Jen,The pad is a carbide impregnated nylon which gets just the right amount of key needed for good adhesion. No, you mustn't sand blast back to the cast iron. I think Andy has already discussed this with someone earlier in this forum. You will just open up a can of worms if you do so. It's best to prepare on the existing surface. I am assuming it has not been resurfaced in the past. If so, this would have to be completely stripped off.
I dont know what you mean by D A You will have to elaborate.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 12:31 PM
|
jen
Joined 18 Jun 2004
14 posts
|
Hi Tubbyuk, right, that clears that up! ok, judging from the look of the inside of the bath, it looks like someone has tried to DIY it before, but obviously not very well (it looks like it's been brushed on) so as you have said. this will all need to come off. A D.A is a sander. It stands for Dual Action. It's an orbital sander on which the counter balance can be locked to make it a 'normal' sander. good bit of kit, takes the hard work out of sanding!!! so what do you reckon?
Jen
|
Re-enamelling a cast iron bath
2 November 2004, 12:37 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Hello Alex,Sometimes a bath that looks absolutely horrendous with bad stains etc is not as bad as it seems. Feel the surface all over with the tips of your fingers. Is the surface still smooth and undamaged? If so, maybe that old man of the north "superman" or whatever can polish it for you after all. If however it is rough as a goats knee then you will have to have it resurfaced or DIY.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 12:48 PM
|
Alex
Joined 16 Oct 2004
9 posts
|
Only have experience with sheep, haha. The surface is not smooth, there are lots of shallow lines like it has been scratched where the wet pine needles had been sitting in the center of the bath so I suspect it will need to be sanded/filled. Is it still worth resurfacing? Alex
|
Re-enamelling a cast iron bath
2 November 2004, 12:49 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Hey Jen,
You are a sucker for punishment! You don't need that much sweat, not to mention the awful clouds of dust you will be covered in with your double whatsit. Get yourself a litre of Nitromors stripper ( green tin all purpose) paint it on, and scrape the lot into the bottom of the bath and then scoop it all onto 4 layers of the Washington Post. When dried out, chuck away.
Wash down thoroughly and you are ready to begin preparation.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 1:02 PM
|
jen
Joined 18 Jun 2004
14 posts
|
that sounds a bit easier! so after the crap is cleaned off with the nitromors, next course of action would be???? your pregnant carbide doofer? or is that just a con to make me buy more of your products! Ha ha!
Jen
|
Re-enamelling a cast iron bath
2 November 2004, 1:13 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Alex,That is a question you should never ask anyone who is in this business. We are all with one mind in favour of you doing something with that bath, pine needles or sheep aside, it makes no difference.
Common sense asks however: Is there some special attachment to this particular bath?
The basis upon which the service of bath resurfacing operates is primarily that of saving money. e.g. Doing the work in situ with no tiling, plumbing and other costs involved. Nowadays of course it also affords the opportunity of keeping the cast iron baths.
In your case, it sounds like you haven't even got the bathroom yet, why not just put a whole new suite in using a good quality British made enamelled pressed steel bath? Just a thought.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 1:29 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Hey Jen,If we carry on like this, you will be in the bath resurfacing business and I will have to go and join Andy on the Riviera and play drafts. You don't absolutely need the pad but for someone who has a D/A in her workshop this pad would look nice hanging on the wall with all those other pieces of kit. Whatever you decide I'm sure its going to be fun.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 1:42 PM
|
Andy
Joined 22 Oct 2003
65 posts
|
Alex . Mr Tubby has hit the nail on the head with this one .The main purpose of resurfacing is to solve a particular problem.
What to do with a bath that is FITTED and in bad condition .
It is a very cost effective solution to this problem .
Its only other purpose is where there is a special personal attachment to the bath . ie it belonged to my Granny/ Aunt /Solicitor .
It sounds like none of these apply in your case and you would be well advised to think about fitting a steel bath . These are cheap and fairly durable . (Just dont overtighten the feet !)
Thats my twopence worth . .............................................I'll get me coat ...
|
Re-enamelling a cast iron bath
2 November 2004, 5:00 PM
|
Alex
Joined 16 Oct 2004
9 posts
|
You have a point and I have been wondering whether to let the sheep use it. Thing is, I have a beautiful old washbasin and it needs to go with a roll top bath. The cottage is within the walled garden on the Earls of Galloway estate, so we are trying to put character in, but a bit of luxury too. It's meant to be the real country living experience, you know Rayburn, wood burner, roll top bath, fresh eggs on the doorstep etc. Maybe a few of you preloved members can let me know what you think? Is a holiday in a country cottage in a beautiful part of Scotland going to be improved by the charm of a roll top bath or would you rather have a cheap and cheerful plain new white bath? I've advertised it already with a roll top bath as you can see on http://www.escapetogalloway.co.uk but I can change that.
|
Re-enamelling a cast iron bath
2 November 2004, 5:01 PM
|
jen
Joined 18 Jun 2004
14 posts
|
hi Tubbyuk, what can I say, I like my power tools!!! Thanks for your help, I'll give it a go and let you know the results! (by the way, if it's crap it'll be your fault!!!!) ha ha!!! Keep up the banter, it's a great source of entertainment (as long as no-one calls me YEN!) Cheers.
|
Re-enamelling a cast iron bath
2 November 2004, 5:08 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
You can have us all up there for a try out. I am sure we could even offer you a discount.
It sounds ideal so you make a decision and jump in.
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 5:13 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Jen,
I have a yen to know where you got your kit from? what was the service like? Delivery etc.?
|
Re-enamelling a cast iron bath
2 November 2004, 5:34 PM
|
jen
Joined 18 Jun 2004
14 posts
|
Tubbyuk, what kit are you on about? haven't bought one yet, just needed to know prep details to weigh up whether it'd be worth it. When I do get round to buying one it'll probably be from your website though unless you recommend anywhere else!?
|
Re-enamelling a cast iron bath
2 November 2004, 5:44 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Jen, Sorry, the way you were talking it sounded like you were starting and that I was going to be in trouble if you dont work properly.
You could buy at several sites but you wont get to talk to anyone who can talk you through the procedure etc. You are in Devon are you not?
Cheers
|
Re-enamelling a cast iron bath
2 November 2004, 5:57 PM
|
jen
Joined 18 Jun 2004
14 posts
|
Sorry if it sounded that way, unfortunately I am a sarcastic cow! but I don't wish to offend anyone! yep, I'm in Devon. cheers.
|
Re-enamelling a cast iron bath
2 November 2004, 6:03 PM
|
Alex
Joined 16 Oct 2004
9 posts
|
Thanks for the vote of confidence Tubby UK. But I do have a serious question for all you specialists, as we are so close to the beach we will get sand in the bath. Does that rule out any resurfacing?Alex
|
Re-enamelling a cast iron bath
2 November 2004, 6:21 PM
|
Tubbyuk
Joined 30 Apr 2004
58 posts
|
Hello Alex,It wont matter a jot what you do, resurface or new, sand is sand and will scratch any surface over time. Thats why we attach sand to paper and call it sandpaper.
Shoot the guests after they have paid if they dont wash their feet off before getting into your bath.
Seriously, it seems that you now have to decide which option you are going to have to choose.
1. Have your bath resurfaced professionally every couple of years.
2. Replace the bath every, maybe three years.
3. Allow £25 per year and use a Tubby every 2 years.
When you go to the races Alex, I am assuming you are aware that you only win when you put your money on the winner.
Cheers
|
Re-enamelling a cast iron bath
3 November 2004, 8:54 PM
|
Reg
Joined 3 Nov 2004
18 posts
|
How did the baths stand up to prolonged use?Also do you know of a firm in the Notts area who do in situ re [Log in to view email]
|
Re-enamelling a cast iron bath
10 November 2004, 7:28 PM
|
Beth
Joined 10 Nov 2004
1 posts
|
Loads of really helpful info on resurfacing enamel baths, but I'm struggling to find details of a recommended professional who works in the South Wales area. Noticed the message from "gazz" but assume he lost the fight with his kids for use of the pc, as he doesn't seem to have to say!?I'd really appreciate any suggestions as I'm trying to sort this out for my Gran - if the promise of freshly baked welsh cakes could entice gary or andy to venture to these parts they wouldn't be disappointed!
Messages 221
to 240
of
834.
« Previous
1
...
6
7
8
9
10
11
12
13
14
15
16
17
18
...
42
Next »
Important Note
All messages are submitted by visitors to this web site, and represent their own personal opinion. They do not necessarily represent the views or opinions of Preloved.
You use this information at your own risk. Preloved can not be held responsible for any damages or loss resulting from the use of this site. Please see our Terms and Conditions for more details.
|
More discussion in