|
GOT A OUTBOARD PROBLEM?
Messages 1
to 16
of
16.
 |
GOT A OUTBOARD PROBLEM?
16 March 2000, 0:00 AM
|
boatmad
Joined 16 Mar 2000
4 posts
|
If you have a outboard problem give me a call I have a wide knowledge with these s.o.b's
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
18 March 2000, 0:00 AM
|
bravo
Joined 29 Feb 2000
2 posts
|
If I had a defective piston (enough to need it replaced) what would the symptoms be
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
24 March 2000, 0:00 AM
|
philly
Joined 24 Mar 2000
1 posts
|
I HAVE A MARINER 60HP 1995, IT HAS DONE LESS THAN 50 HOURS AND IT WILL NOT CHARGE .AT THE BATTERY LEADS ITS ONLY 12.1 VOLTS ........ HELP.. PHIL
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
24 March 2000, 0:00 AM
|
boatmad
Joined 16 Mar 2000
4 posts
|
IT SOUNDS LIKE YOU HAVE A CHARGE COIL DOWN REMOVE FLYWHEEL AND CHECK ALTERNATOR COILS FOR CONTINUITY OR LEAKAGE. BEST OF LUCK. SYD.
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
24 March 2000, 0:00 AM
|
boatmad
Joined 16 Mar 2000
4 posts
|
you should test your compression with a compression tester you would get poor running performance and hard starting
just to mention a few symptoms good look syd
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
20 April 2000, 0:00 AM
|
coolit
Joined 20 Apr 2000
1 posts
|
can I run a 1992 mercury 75 on unleaded
fuel without modification?
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
26 May 2000, 0:00 AM
|
lynn
Joined 25 May 2000
1 posts
|
can you help please,1974 johnson 40hp
manual start.fuel dripping out of carb
when running,leaf valve seems okay,
could this be caused by pumping the fuel
bulb to hard causing to much pressure.
any help tuning and starting would be welcome ie. setting and adjusing the slow running needle valve ect;satch i got this nickname from the bowery boys
as a kid thanks
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
2 June 2000, 0:00 AM
|
THOR
Joined 2 Jun 2000
1 posts
|
I have a mercury 850 how do i get the rotor arm off!
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
1 July 2000, 0:00 AM
|
Martin
Joined 25 Jun 2000
1 posts
|
I have a Mercury 800. The engine runs fine but the gearbox has siezed up and has cracked the housing just forward of the prop. Do you know where I can get an affordable replacement gearbox and lower section?
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
1 July 2000, 0:00 AM
|
doggyboys
Joined 1 Jul 2000
1 posts
|
i'm looking to buy a small outboard motor for lake fishing. any idea which are the best. what should i look for in the used one's. also where is the best place to get one second hand thanks
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
15 August 2000, 0:00 AM
|
vince
Joined 15 Aug 2000
1 posts
|
I have an evenrude 9.9
outboard that was running fine but now will only run on tick over if i open up the throttle it dies
I have cleaned the carb completely
changed the plugs and am totally fed up with out board engines
I am a by trade a hgv mechanic with little experience with two strokes and now wish to burn the bloody thing please help
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
24 August 2000, 0:00 AM
|
Bob
Joined 24 Aug 2000
1 posts
|
I know the feeling im a diesel fitter myself And wish I had never brought a petrol let alone a fxxxing 2 stroke
never had so much grief in my life
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
21 April 2003, 0:00 AM
|
itscarl
Joined 21 Apr 2003
1 posts
|
hi i have a suzuki 115hp and have lost forward drive it works fine in reverse put it into forward and nothing there accelerate a little and it jumps in and out of reverse for a split second disconnected gear selector cable and put it into forward and still did the same im going to have a look myself anything i should know before i strip it
thanks carl
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
22 April 2003, 0:00 AM
|
Stephen
Joined 22 Apr 2003
3 posts
|
I inherited a 1975 Evinrude 25 on the back of a decent Dejon 14. I'm told the engine needs @£200 worth of work on the electrics with no guarantees that this will result in an engine that runs reliably. It keeps cutting out apparently. It's a 'bitser', ie has got canabalised bits from other engines. Any idea on the history of these engines? Am I better in putting the £200 towards a newer second hand engine at the £650 mark? Sorry, but can't be more specific than this - not much help - just trying to share a problem! Steve.
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
3 September 2003, 0:00 AM
|
BigTwin
Joined 3 Sep 2003
1 posts
|
We have an Evinrud Big twin 40. I have been rebuilding the gearbox. I have been able to secure all the parts excep the gearbox oil seal. Does anyone out there have any Idea where I can get one.
Discussion Archived
|
GOT A OUTBOARD PROBLEM?
27 September 2003, 0:00 AM
|
Stephen
Joined 22 Apr 2003
3 posts
|
Try Mitchell Outboard Services in Glasgow. They got me all sorts of bits for my Evinrude. Very helpful and reliable. Will post out stuff and takes credit cards.
Discussion Archived
Messages 1
to 16
of
16.
Important Note
All messages are submitted by visitors to this web site, and represent their own personal opinion. They do not necessarily represent the views or opinions of Preloved.
You use this information at your own risk. Preloved can not be held responsible for any damages or loss resulting from the use of this site. Please see our Terms and Conditions for more details.
|
