ALL CARVER CASCADE WATER HEATER, GAS FIRE, FANMASTER,P4 QUESTIONS HERE
Messages 2581 to 2600 of 3089. « Previous 1 ... 124 125 126 127 128 129 130 131 132 133 134 135 136 ... 155 Next »
Thanks and same as joe let me know how and when to order please
Message for Gary or Keith can one or both of u help a fridge works ok on electric but on gas pilot ligh works but turn dial and burner does not trip in Roy
Still looking for the fault causing my fan to only run slowly. Regards, Peter
I've a feeling it will be this transistor that's failed in the 'slow' position and needs replacing. One other possibility is the fan motor is faulty, try putting 12v direct to it to test. ___________________ website: http://www.arcsystems.biz email: [Log in to view email] If you want to add your own question, just click on any 'reply to this message'
___________________ website: http://www.arcsystems.biz email: [Log in to view email] If you want to add your own question, just click on any 'reply to this message'
Further as my websites been hacked I'll give the address here so you know where to send the cheque made to 'Arc Systems' ready for my return 13 Far Street, Bradmore, Nottingham, NG11 6PF. I'm not there but someone always is If you want to add your own question, just click on any 'reply to this message'
I meant to ask you if I could try putting 12v direct to the fan ,to check it out. Will do this tomorrow and if ok, will order a new pcb. Regards, Peter.
Just a message to thank you for your expert advice. Have changed the fan pcb and all working correctly. Away for a few weeks, from mid March, but on return will be looking to improve the 240v heating by getting a remote sensor, possibly up dating Thanks again, Peter
If you do feel like fitting one of my serviced exchange modules yourself, (being designed to 'self fit' it is very straight forward), you will then save about 2/3rds of that £196. If you want to add your own question, just click on any 'reply to this message'
Adverts Currently On Preloved - Place an ad here for free
The Carver 3002 is a re-badged Truma 3002, they are then one in the same fire!! all your fire needs (should it actually need them) is a new pair of jets. I've got a bag full of new Carver/Truma 3002 jets but my concern is it's does not need them and something else is amiss? I'm wondering if in fact the 'gauze' on the top of the main burner is loose and lifting when it gets hot, this will cause the flame pattern to be erratic same as if the jet was at fault? If you want to add your own question, just click on any 'reply to this message'
The Carver 3002 is a re-badged Truma 3002, they are then one in the same fire!! all your fire needs (should it actually need them) is a new pair of jets. I've got a bag full of new Carver/Truma 3002 jets but my concern is it's does not need them and something else is amiss? I'm wondering if in fact the 'gauze' on the top of the main burner is loose and allowing it to lift when it gets hot, this will cause the flame pattern to be erratic same as if the jet was at fault? Or simply a partly obstructed gas/air inlet tube inside the burner if the flame is yellow, a bit of a spiders web is generally the cause of this.
If you want to add your own question, just click on any 'reply to this message'
thanks again tony
I can supply the jets when I return, but, I don't for one second think they will cure your problem by themselves let alone overhaul it!!
If you want to add your own question, just click on any 'reply to this message'
New here but looks like the best place for my question. I have a Carver 2000P Space Heater missing the connecting rod from the control knob. I am not sure if there is a cable missing also Please see my photo. Any advise and where I could get the parts would be great. I have the bottom piece (controller) but its not in the pic. 
Two wires are required, one from piezo to burner for spark, the other is an earth wire from the bottom of the holder to one of the 8mm brass nuts that hold the silver coloured support bracket.
If you want to add your own question, just click on any 'reply to this message'
How do I get my hands on one of these rods? Ihave the holder, I think. The missing rod goes in the top and the bottom rod out of the holder goes into the baseblate where I take it the main gas control is? Cheers
My address details are above on this page and you can email direct from link below
If you want to add your own question, just click on any 'reply to this message'
Messages 2581 to 2600 of 3089. « Previous 1 ... 124 125 126 127 128 129 130 131 132 133 134 135 136 ... 155 Next »
Important NoteAll messages are submitted by visitors to this web site, and represent their own personal opinion. They do not necessarily represent the views or opinions of Preloved. You use this information at your own risk. Preloved can not be held responsible for any damages or loss resulting from the use of this site. Please see our Terms and Conditions for more details. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Not a member yet?Why not join the fun for free! Members can sell their stuff completely free of charge, have searches prioritised for their local area, and lots more. Join for free | Member Log In
Are you a fan of Preloved?
If so, why not help us spread the Joy of Second Hand by joining us on Facebook. [more...] |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
More discussion in